SHYSKY 24V 150W DC Brushless Water Pump - 8000 LPH Flow, 10m (32ft) Lift, IP68 Waterproof, Low Noise - Ideal for Hydroponics, Aquariums, Pond Filtration & Industrial Cooling Systems

Product Description

DC80E-24100S-1 Micro Brushless DC Water Pump Dimension and weight 185mmx100mmx136mm; Approx.2.25 Kg External diameter of outlet 32mm (1" thread) External diameter of intlet 32mm (1" thread) Driving mechanism Brush-less, magnetic isolated design Material of pump shell ABS,PES/SPS/PPS/PA66+30%GF (Optional when customization at MOQ) Condition of use Support continuously work, submersible or land use (note that pump cannot be not self-priming) Suitable medium Water, oil, etc (corrosive or special fluids shall be tested in advance.) (Pre-test needed for special liquid) Max working temperature 100 ~ 120℃(for S/A sub-series) Power consumption 150W for 24VDC Rated voltage 24Vdc Working voltage range 12Vdc ~ 26Vdc Max load current 6.3A for 24VDC Max horizontal flow rate 8000 L/H @ 24VDC (2113GPH) Max static lift 10M @ 24VDC (32ft) Noise class <40dB, at 1m distance Waterproof class IP68(suitable for submersible installation) NOTE: DC80E-24100S-1 (NEW) Water pump, 24VDC, 150W, 3-phase brushless DC design, soft start, with both ports being 1" threaded (with external diameter of appr. 32mm). Max static lift is about 10 meters (~33 ft), while Max horizontal flow rate is up to 8000 LPH (~2100 GPH). No direct AC powering (unless with power adapter), No DRY WORK! Please pay attention. When getting the pump, it’s recommended that water test be done independently in advance. As to control box of pump, strictly speaking, it’s not recommended to be located in the water; if indeed have to, waterproof tape is recommended to be firmly wrapped in advance. Of course, location out of water is more recommended. Kindly Note: It is only the whole set of pump that is included, with rated voltage of DC power 24V. NO power supply is offered. About the rectangle-shaped metal box, it is the controlbox (brain) part of the pump product, and it is NOT power adapter. Please be not confused. DRY RUN Protection will be automatically triggered when there exists in-sufficient/ no water flow in the circulation system. DRY-RUN PROTECTION feature description: Pump works at rated voltage: When there exists insufficient in-flow / no in-flow / significant bubbles inside the water flow, pump will access status of stop-run-stop-run-stop-runcycle. When in-flow comes sufficiently again, pump will re-access normal work status. It is aimed to protect pump from long continuous DRY RUN in the system, which will physically damage the rotor and pump connection part. Pump could die due to this. [High Power Efficiency] SHYSKY DC80E-24100S-1 Heavy Duty Water pump, Both inlet and outlet G1'' threaded ports, with external diameter of appr. 32mm; Max static lift 10m (~32.8ft); Max horizontal flow rate 8000LPH.Typical feature is with high flow rate and good lift value, suitable for cooling, circulation, gardening systems. [BLDC design] Brushless DC motor, also known as EC motor; Magnetic Driven (NO DIRECT AC 100-240V POWER CONNECTION, PROHIBITED); Small size but strong; Low consumption & High Efficiency; Long time continuous working with low noise;No spark, Explosion - proof; Low noise about 40dB. [Variety Power] 24V DC electric source, Battery, Solar Panel, etc; Soft Start with Low in-rush current, Especially suitable for Solar SYS which can not provide instant startup impulse current. Constant power level when powering vol. is over 24VDC yet under 28VDC, quite useful feature in some cases. [Wide applications] Low-voltage safety, high power-efficiency, low noise at normal work and supporting long-time continuous reliable running. This pump is widely applied for fountain landscape, medical equipment cooling circulation, air compressor cooling circulation, PC server water cooling, yacht/ vehicle water cooling, or other industrial, medical and household water processing systems. Pump cannot be self-priming, and it is important to make sure that there exists no dry run (especially for long time). Avoid impurities in the pumping systems. About the use of micro brushless pump product, here are several notes and hope they can be helpful: 1, as micro brushless dc pump, it works via electronic commutation while not brush friction, so there exists no loss caused by brush friction. Pump works with relatively high efficiency. stator part is completely potted inside pump body with epoxy material, physically separated from external fluid environment and completely waterproof. 2, Pump supports continuous long time work with relatively low noise at normal working environment.land use or submersible installation can be both OK, but it cannot be self-priming, just make sure that fluid can actively flow passing through inlet/outlet because pump works via centrifugal force of high-speed rotation of impeller inside (push/throw fluid out). No long-time dry work without fluid, or it may damage the pump. 3, It is suggested that the max volt of power supply be within 14VDC (Pumps with 12V rated volt.)/26VDC (Pumps with 24V rated volt.). 4, For static lift value, it means the max vertical height of flow column when outlet is connected with external matching hose/tube, when pump works at rated voltage. For max flow rate value, it means the max flow rate of pump at horizontal level, when pump works at rated voltage. The higher the height, the lower the flow; when height reaches lift value, flow rate becomes zero. Note that lift value and spraying/shooting height of pump are completely different. So dear users, please do not be confused by them. Certain deviation of around +-10% is advised to be left when in relevant applications, to leave enough margin. 5, If AC/DC power adapter is adopted to power the pump, output capacity is suggested to be 24VDC, 8A/ more. If less, adapter may be not powerful enough to power the pump. Other DC power supplies will be okay too, when matching. 6, Wire connector specification: This pump is a high-power device, its connector adopts a relatively special 4 PIN connector specification, to withstand high power consumption. If we as users violently cut the connector off, we will see that there will be ONE cable within, which is Positive, while THE OTHER cable within, which is Negative. Being connected with external matching 24V DC Power Supply.